Moving plumbing in concrete slab

Can you move plumbing on a concrete slab?

Under slab plumbing lines can be moved , but when it’s done in a finished space, the can be very dirty and somewhat expensive. In most cases, a home constructed on a concrete slab has the main water line entering from the exterior the below the slab and then it comes up in a utility or laundry room.

Can you move a toilet on a concrete slab?

If your bathroom is on top a concrete slab , we have some bad news. To move the toilet more than just a couple of inches, you will have to demolish the concrete to access and relocate water and waste lines. Then you will have to rebuild the concrete foundation and replace the sub-flooring, flooring, and fixtures.

Can you add a bathroom on a slab?

When homes are built on a slab , the plumbing is laid before the concrete slab is poured. You can add plumbing after the fact, but it is labor intensive. This is similar to adding a bathroom to an existing basement. We then pour concrete into the trench to level the slab , and the new floor is covered with ceramic tile.

Is it hard to move toilet plumbing?

Moving a toilet is not so much about moving the actual fixture—in fact, installing a toilet is a simple job that takes less than an hour—as it is about moving the drainage and the water supply plumbing to the new location. Once all of the plumbing is in place, installing the toilet is a relatively easy task.

How is plumbing run in a slab home?

During the plumbing slab construction, the pipes are buried in gravel or sand beneath the slab and are (obviously) difficult to access. The plumbing through slab isn’t easy to reconfigure once placed. Modern homes are more likely to have a moisture barrier that protects a concrete slab .

You might be interested:  Plumbing tape for leaks

What does it cost to move a toilet drain in concrete slab?

The cost to move a toilet or sinks can be $2,500-$3,500 per fixture. Plumbing can be a significant cost factor in a remodel when a bathroom floor plan is altered. The toilet is the most expensive to move .

How do you install a toilet on a concrete floor?

Installing a Toilet on a Concrete Floor Step 1: Place the Flange. Place the toilet flange face down on the concrete . Step 2: Drill Holes for the Flange. Next, use a marker to mark the concrete right where the four holes in the flange are. Step 3: Clean the Area. Step 4: Attach the Flange. Step 5: Finish the Flange Installation . Step 6: Connect the Toilet .

Can a shower and toilet share the same drain?

Here’s the longer answer: Your shower and toilet most likely share a drain line and a vent stack (this setup is called wet venting, more on that later). If either the line or the stack has a clog or blockage, air is forced either up or down your toilet , making the gurgling noise you’re hearing.

Can you run water pipes in a concrete floor?

Without a doubt, the best practice is to use flexible pipe solutions made from PEX or polybutylene, such as the JG Speedfit Layflat® range of pipes and conduits. Installers may also wish to consider the ‘ Pipe in Pipe ‘ solutions. The concept is simple – pre-sleeved pipes , ready to lay within concrete or masonry.

Can I install a toilet in my garage?

You can put a toilet in your garage but will almost always need a permit to begin work. There are guidelines for how large the room is and how much space is around the toilet that must be followed. You’ll also need to consider the cost of of any structural changes needed to add the plumbing.

You might be interested:  Residential plumbing services

Can I add a bathroom in my garage?

With careful planning and the help of innovative upflush plumbing fixtures, it is possible to add a bathroom to virtually any home, according to SFA Saniflo Inc. Adding a bathroom in a basement, garage area or in a home that sits on a slab traditionally requires cutting into concrete.

How do you break concrete without a jackhammer?

Tool #1: Sledgehammer + Pry Bar Recruit a buddy to lift a corner with a pry bar. Start slamming at the corners and work your way towards the center. Pry and pull out the broken chunks as they break apart. Don’t hit the same spot twice. Keep moving and keep lifting with that pry bar.

How do you cut a 4 inch concrete slab?

Use a standard circular saw, equipped with a corundum or diamond blade, for small tasks. For slabs , it’s best to cut through the top inch , then use a sledgehammer to break off the rest. The jagged edge left below the cutting line provides a good rough edge for the new concrete to bond to.

Leave a Reply

Your email address will not be published. Required fields are marked *